Indice del forum

Udu Biologia Lecce

Gli studenti di biologia di Lecce

PortalPortale  blogBlog  AlbumAlbum  Gruppi utentiGruppi utenti  Lista degli utentiLista degli utenti  GBGuestbook  Pannello UtentePannello Utente  RegistratiRegistrati 
 FlashChatFlashChat  FAQFAQ  CercaCerca  Messaggi PrivatiMessaggi Privati  StatisticheStatistiche  LinksLinks  LoginLogin 
 CalendarioCalendario  DownloadsDownloads  Commenti karmaCommenti karma  TopListTopList  Topics recentiTopics recenti  Vota ForumVota Forum

Antibacterial floor
Utenti che stanno guardando questo topic:0 Registrati,0 Nascosti e 0 Ospiti
Utenti registrati: Nessuno


 
Nuovo Topic   Rispondi    Indice del forum -> Parole al Vento
PrecedenteInvia Email a un amico.Utenti che hanno visualizzato questo argomentoSalva questo topic come file txtVersione stampabileMessaggi PrivatiSuccessivo
Autore Messaggio
qizhenapp








Registrato: 14/09/16 08:13
Messaggi: 7727
qizhenapp is offline 






MessaggioInviato: Gio Ott 18, 2018 7:32 am    Oggetto:  Antibacterial floor
Descrizione:
Rispondi citando

Oxidation corrosion is one of the fatal flaws in product parts. In the past, the heat treatment of many products of a company in China was quenched by salt furnace. When the rainy season came, the parts had to be surface treated within one week. Otherwise, the residual salt would corrode the workpiece, which would lead to the quality problem of batch scrapping. In this season, the surface treatment of the product parts is usually carried out immediately after heat treatment to solve this problem. However, due to the large output and variety of the product parts, this practice increases the workload of the surface treatment workshop during the construction period, resulting in production arrangements. The pressure on it. In order to alleviate this pressure and achieve balanced production, the company introduced the VQ02-100 oil quenching vacuum furnace.

Oxidation corrosion is one of the fatal flaws in product parts. In the past, the heat treatment of many products of a company in China was quenched by salt furnace. When the rainy season came, the parts had to be surface treated within one week. Otherwise, the residual salt would corrode the workpiece, which would lead to the quality problem of batch scrapping. In this season, the surface treatment of the product parts is usually carried out immediately after heat treatment to solve this problem. However, due to the large output and variety of the product parts, this practice increases the workload of the surface treatment workshop during the construction period, resulting in production arrangements. The pressure on it. In order to alleviate this pressure and achieve balanced production, the company introduced the VQ02-100 oil quenching vacuum furnace. 1. Parts processing technology analysis and new equipment support capability A variety of product parts produced by a domestic company are thin-walled, complex-shaped parts with folded edges, no through-holes, etc., and require no oxidative decarburization on the surface after heat treatment. The process uses a salt bath furnace to heat, although it can effectively prevent decarburization, but often residual salt is retained on the surface of the workpiece. Because it is difficult to clean thoroughly, it is caused by oxidative corrosion. The workpiece is heated in a vacuum to remove surface grease, decompose the oxide, and the surface is activated to improve surface quality. VQO-100 double chamber quenching and tempering furnace can guarantee the condition of high vacuum (10Pa). Firstly, it fully meets the requirements of non-oxidative decarburization and heating quenching of the workpiece. Secondly, the equipment is controlled by the program and automatically executes the set process parameters. The influence of human factors is ruled out; again, the temperature control system adopts PID to adjust the temperature automatically, and the uniformity of the furnace temperature can be controlled within 2 C.

Related products:


read more:
<ul><li><a href="https://www.antsalliance.com/news/Multi-arc-Ion-Vacuum-Coating-Machine.html">Multi-arc Ion Vacuum Coating Machine</a></li>
<li><a href="https://www.antsalliance.com/pump/liquid-ring/2BE1-103-liquid-ring-vacuum-pump-with-1750rpm-rotary-speed.html">2BE1 103 liquid ring vacuum pump with 1750rpm rotary speed</a></li>
<li><a href="https://www.antsalliance.com/news/The-use-of-rotary-vane-vacuum-pump.html">The use of rotary vane vacuum pump</a></li></ul>
Torna in cima
Profilo Messaggio privato
Adv



MessaggioInviato: Gio Ott 18, 2018 7:32 am    Oggetto: Adv






Torna in cima
Mostra prima i messaggi di:   
Nuovo Topic   Rispondi    Indice del forum -> Parole al Vento Tutti i fusi orari sono GMT + 1 ore
Pagina 1 di 1

 
Vai a:  
Puoi inserire nuovi Topic in questo forum
Puoi rispondere ai Topic in questo forum
Non puoi modificare i tuoi messaggi in questo forum
Non puoi cancellare i tuoi messaggi in questo forum
Non puoi votare nei sondaggi in questo forum
Puoi allegare files in questo forum
Puoi scaricare files da questo forum





Udu Biologia Lecce topic RSS feed 
Powered by MasterTopForum.com with phpBB 2003 - 2008